View AT-160160AFIQW-49H_4624525.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

A MP I R E
SPECIFICATIONS FOR LCD MODULE
CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED DATE
Approved For Specifications Approved For Specifications & Sample
AT-160160AFIQW-49H(V)(R)
BY
APPROVED BY
CHECKED BY
ORGANIZED BY
Date : 2007/3/3
AMPIRE CO., LTD.
1
RECORD
Revision Date 2007/3/3 Page New Release
OF REVISION
Contents Editor Edward
,
Date : 2007/3/3
AMPIRE CO., LTD.
2
1
(1) (2) (3) (4) (5) (6) (7) (8)
Feature
Display format : 160 x 160 dot-matrix Construction : FSTN LCD, TAB IC ,White Edge LED back-light, FFC and PCB. Display Type : FSTN, Transflective, 6 o'clock view. Controller : New Version RA8835. 5V or 3.3V single power input. Built-in DC/DC converter for LCD driving. Extended temperature type. 80 or 68 Family MPU Selectable by Jumper Setting. ROHS compliant.
2
MECHANICAL DATA
Parameter Dot size Dot pitch Viewing area Module size Stand Value 0.335(W) x 0.335(H) 0.35(W) x 0.35(H) 60.1(W) x 60.0(H) 69.0(W) x 69.5(H) x 8.9 max (T) Unit mm mm mm mm
3
ABSOLUTE MAXIMUM RATINGS
Parameter Logic Circuit Supply Voltage LCD Driving Voltage Input Voltage Operating Temp. Symbol VDD-VSS VADJ-VSS VI TOP TSTG Min -0.3 -0.3 -0.3 -20 -30 Max 7.0 26.0 VDD+0.3 70 80 Unit V V V C C
Extended temp. type Storage Temp.
Date : 2007/3/3
AMPIRE CO., LTD.
3
4
ELECTRO-OPTICAL CHARACTERISTICS
Parameter Logic Circuit Supply Voltage Symbol Condition Min Typ Max Unit Note
----- Electronic Characteristics ----VDD-VSS --20C 0C LCD Driving Voltage VADJ-VSS 25C 50C 70C Input Voltage Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range VIH VIL IDD --VDD = 5V 2.7 19.8 18.4 17.0 15.6 14.1 0.8 VDD VSS 35 -20.8 19.4 17.9 16.4 14.8 --40 5.5 21.8 20.4 18.8 17.2 15.5 VDD 0.2 VDD 45 V V mA V V V V
----- Optical Characteristics ----CR Tr Tf f b l r Frame Frequency fF 25C 25C 25C 25C 25C & CR2 2 --30 40 40 35 -5 150 290 ----70 -225 435 -----Hz Deg. ms ms Note 3 Note 1 Note 2
----- White LED Back-light Characteristics ----Parameter Forward Current Symbol IF Condition -IF=60mA IF=60mA IF=60mA IF=60mA Min ---0.28 0.29 Typ 60 9 3.2 0.31 0.32 Max 80 -3.5 0.34 0.35 Unit mA cd/m2 V Note Note 4 & 7 Note 4 Note 5 Note 6
LCM Luminous intensity (Full White pattern) Forward Voltage LED C.I.E VF X Y
Note 4: Luminous intensity is decided by forward current of White LED. Note 5: White LEDs are with voltage tolerance Note 6: White LEDs are with color tolerance
Date : 2007/3/3
AMPIRE CO., LTD.
4
LED Dice Number4 LED
(NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state)
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2007/3/3
AMPIRE CO., LTD.
5
Note 7 : One LED
5
BLOCK DIAGRAM
Date : 2007/3/3
AMPIRE CO., LTD.
6
6
POWER SUPPLY CIRCUIT
+25V
VLCD
VDD
DC/DC Converter LCD Bias Circuit
VADJ
VSS
Date : 2007/3/3
AMPIRE CO., LTD.
7
7
INTERFACE DEFINITION
CN1: Interface of pure driver (No Use in this LCM) PIN NO. 1~20 SIGNAL NC LEVEL No Connection FUNCTION
CN3: LCM with Built-In Controller PIN NO. 1 2 3 4 5 6 ~ 13 14 15 16 17 18 19~23 24 SIGNAL /RESET /RD /WR /CS A0 DB0~DB7 VDD VSS VLCD VADJ LED_A NC LED_K ---LEVEL H/L H/L H/L H/L H/L H/L FUNCTION Reset Signal 80 Series: Read Signal 68 Series: Enable Signal(E) 80 Series: Write Signal 68 Series: R/W Signal Chip Select Signal Data Type Selection Data Input(8 bits) Power Supply for Logic(+5.0V) Power Supply(Ground : 0V) Positive voltage output (+25V) Contrast Adjustment Input ( VADJ-VSS = LCD driving voltage ) LED A=+V No Connection LED K=Ground
X1, X2, Y1, Y2 for Touch Panel (without Touch Panel Controller)
Date : 2007/3/3
AMPIRE CO., LTD.
8
8
TIMING CHARACTERISTICS 8.1 8080 Family Interface Timing
Date : 2007/3/3
AMPIRE CO., LTD.
9
8.2
6800 Family Interface Timing
Date : 2007/3/3
AMPIRE CO., LTD.
10
DB0~DB7
9
INSTRUCTION SET
Code Command /RD /WR A0 D7 0 0 0 0 0 0 0 0 0 0 0 0 0 D6 1 1 1 1 1 1 1 1 1 1 1 1 1 D5 0 0 0 0 0 0 0 0 0 0 0 0 0 D4 0 1 1 0 1 1 0 1 1 0 0 0 0 D3 0 0 1 0 1 1 1 1 1 0 0 0 0 0 1 1 0 0 D2 0 0 0 1 1 1 1 D1 0 1 0 0 0 0 D0 0 1 D 0 1 0 40 Initialized Device and display 53 Enter Standby mode 58, Enable and disable display and 59 display flashing set Display start address and 44 display regions 5D Set cursor byte 5C Set start address of character generator RAM Hex Command Description Command read parameters Number of Section byters 8 0 1 10 2 2 0 1 1 2 2 8.2.1 8.2.2 8.3.1 8.3.2 8.3.3 8.3.6 8.3.4 8.3.7 8.3.5 8.4.1 8.4.2 8.5.1 8.5.2
Class
SYSTEM System SET Control SLEEP IN DISP ON/OFF SCROLL CSRFORM CGRAM Display ADDR. Control CSRDIR HDOT SCR OVLAY Drawing Control Memory Control CSRW CSRR MWRITE MREAD
1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 1 1 1 1 1
CD CD 1 0 1 1 1 1 1 1 0 1 0 1 0 1
4C Set direction of cursor to movement 4F 5A set horizontal scroll position 5B set display overlay format 46 set cursor address 47 read cursor address 42 write to display memory 43 read from display memory
Note: 1. In general, the internal registers of the RA8835 are modified as each command parameter is input. However, the microprocessor does not have to set all the parameters of a command and may send a new command before all parameters have been input. The internal registers for the parameters that have been input will have been changed but the remaining parameter registers are unchanged. 2 bytes parameters( where two bytes are treated as 1 data item) are handled as following: a. CSRW, CSRR: Each byte is processed individually. The microprocessor may read or write just the low byte of the cursor address. b. SYSTEM SET, SCROLL, CGRAM ADR. : Both parameter bytes are processed together. If the command is changed after half of the parameter has been input, the single byte is ignored. 2. APL and APH are 2-byte parameters, but are treated as two 1-byte parameters. 3. Please refer to RA8835 LCD Controller Data Book for detail.
Date : 2007/3/3
AMPIRE CO., LTD.
11
10 JUMPER SETTING
Item MPU Option 80 family (default) 68 family Jumper Setting Pin 1,2 short & Pin 2,3 open on JP3 Pin 2,3 short & Pin 1,2 open on JP3
11 QUALITY AND RELIABILITY 11.1 TEST CONDITIONS
Tests should be conducted under the following conditions : Ambient temperature : 25 5C Humidity : 60 25% RH.
11.2
SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan .
11.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation.
11.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits.
Date : 2007/3/3
AMPIRE CO., LTD.
12
11.5 INSPECTION QUALITY CRITERIA
Item Function Dimension Black spots Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5
Black lines
Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle
Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D0.2 3 4 0.2 0.5 for N = 1 Rainbow color or newton ring. Obvious visible damage. See note 1 See note 2 See note 3
Minor
2.5
Minor Minor Minor Minor Minor Minor
2.5 2.5 2.5 2.5 2.5 2.5
Area A active area Area B view area
Date : 2007/3/3
AMPIRE CO., LTD.
13
11.6 RELIABILITY
Test Conditions Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Temperature Cycle Humidity Test Normal Temp. type 703C , t=96 hrs -203C , t=96 hrs 803C , t=96 hrs -303C , t=96 hrs -30C ~ 25C ~ 80C 30 m in. 5 min. 30 min. ( 1 cycle ) Total 5 cycle 40 C, Humidity 90%, 96 hrs 1,2 1,2 1,2 1,2 Note
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35C , 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. Function of the module should be maintained. Appearance and display quality should not have degraded noticeably. Contrast ratio should be greater than 50% of the initial value.
Date : 2007/3/3
AMPIRE CO., LTD.
14
12 HANDLING PRECAUTIONS
(1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in color. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions.
Date : 2007/3/3
AMPIRE CO., LTD.
15
13 OUTLINE DIMENSION
Date : 2007/3/3
AMPIRE CO., LTD.

16

▲Up To Search▲

Price & Availability of AT-160160AFIQW-49H

	To Download AT-160160AFIQW-49H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .